Hangzhou Suntech Machinery Co., Ltd.
professional manufacturer of pipe tools
Add to Cart
STT150 2 1/2-6" Automatic 900w Portable Electric Pipe Cutter And Threader Heavy Duty
Introduction
This machine is applicable to cutting, threading and inner hole chamfering (the chamferer is optional) of pipes for water, electricity and gas, and has the copying device able to automatically cut the standard taper pipe thread, with a reliable clamping device and an advanced cooling & lubrication system. Therefore, adopting this machine can lengthen the service life of the threading die, and avoid the deformation & slipping of the pipe clamp, so as to obtain the high-quality taper pipe thread. This machine is widely used in equipment installation, building and other industries, regarded as the ideal equipment to improve work efficiency, accelerate project progress, guarantee project quality and reduce labor intensity. (It is an ordinary round-steel threading machine, only applicable to the ordinary round-steel threading. The operating mode and machine structure are basically the same.)
Features
Casing body, brand-new, beautiful appearance.
1100W copper induction motor is driven seperately to avoid burning by oil.
Independent gearbox structure, equipped alloy steel gear, oil lubrication, durable use life.
Two-lever gear design, makes transmission more easy and accurate.
Cast steel shifting structure stronger without cracking risk
Technical data
| Product Name | STT150 2 1/2-6" Automatic 900w Portable Electric Pipe Cutter And Threader Heavy Duty |
| Rotational speed of main shaft | 9/24 r/min |
| Model of die head | 100F Multi-Functional Die Head(2 1/2-4") |
| Self Open Type Copying Die Head(5-6") | |
| Scope of application | 2 1/2-4", 5-6'' |
| Power of motor: | 1100W |
| Gross net weight | 230kg/200kg |
| Packing dimension | 1100mm*740mm*700mm |
| Item | pipe threader |
| Key word | automatic needle threader |
Detail photos
Operation guide:
A. Installation of pipe clamp:
(1) Loosen front and rear chucks, put in the pipe from one side of rear chuck.
(2) Grasp the pipe with right hand, tighten rear chuck first and then tighten front chuck, to fix the pipe. Properly tighten the hammer panel in counter-clockwise direction, so as to clamp the pipe firmly.
(3) After completing threading and chamfering, push the hammer panel in an opposite direction, so as to loosen the chuck.
(4) When clamping a short pipe, the short pipe shall have bevel connection with threading die. In this way, the pipe can determine the center correctly when front chuck is tightened.
B. Preparation for threading
(1) Choose threading die and die head according to your need.
(2) Install threading dies into die head according to their number.
(3) Pull the handle, to lock the threading die.
(4) Adjust the spacing to required scale line.
(5) According to pipe size, adjust scale line of die head to required position, and lock the handle nut.
C. Threading:
(1) Pull the cutting knife frame and chamferer; put down die head to touch the copying block. After reliable positioning of die head, press the button to start the machine.
(2) Rotate the pipe in anti-clockwise direction, rotate the hand wheel of cutting feed, and make die head get close to the pipe.
(3) Apply force to the hand wheel of cutting feed, until die head makes 3 ~4 threads on the pipe.
(4) Then, loosen the hand wheel of cutting feed, so the machine starts automatic threading. When roller of die head goes over copying block and falls down, threading die will open automatically and the threading is completed (Z13 T–M18 threading machine is required to turn back to make the threading die exit). Z1T–50A threading die shall be loosened manually.
(5) Machine halt. Return to the carriage, until the whole die head exits pipe end. Pull out die head, lock the handle and pull up the die head.
Common Faults and Solutions
| Common faults | Reasons | Solutions |
|---|---|---|
| 1. Motor doesn’t work or work with intermittent sound | 1. Fuse is burnt down 2. The plug is not well connected 3. The internal part of the cable is broken 4. The button switch is not well connected 5. 100UF Capacitor breakdown 6. Environment temperature is too low, and lubricating grease solidifies.
| 1. Detect the broken part with a multimeter and use a new fuse 2. Replace the plug or socket 3. Replace the power cord 4. Replace the switch 5. Use a new capacitor 6. Operate indoor or help it to start up |
| 2. Pipe fails to be fixed and slips during threading | 1. Insufficient hammering force 2. Clamping jaw tip turns over 3. One clamping jaw tip breaks or has a gap
| 1. Hammer hard 2. Adjust clamping jaw tip 3. Use a new clamping jaw tip |
| 3. Cutting knife fails to cut, and fails to produce proper threads | 1. Sharp corner of cutting knife is worn out and becomes an arc 2. Pin roll of cutting knife is worn out 3. Cutting force is insufficient
| 1. Replace cutting knife blade 2. Replace pin roll 3. Cut more vigorously |
| 4. Knife cannot cut during threading | 1. Opening of threading die is too small at the start of threading 2. Several teeth of knife head are broken 3. Knife head doesn’t match 4. There is scrap iron in die groove
| 1. Use threading die correctly 2. Replace knife 3. Re-install knife head 4. Clean threading die head |
| 5. Front chuck loosens and falls down | Screws loosen due to long-term use
| Inspect them timely |
FAQ
1. WHO ARE WE?
We are professional pipe machine manufacturer located in Hangzhou city of China starts from 1989, we are close to Port Shanghai, Ningbo as well as Yiwu. We mainly export to North and South America, South Asia and the Middle East countries. Our client are power tools wholesaler and comnpany for specific constrution project such as fire fighting pipeline building etc.
2. HOW CAN WE GUARANTEE THE QUALITY?
We always test at least one pipe on every pipe machine before we ship out.
Some of our heavy duty models works well after even 7 or 8 years according to our client feedback, for all of our machine we offer 12 month warranty.
3. WHAT CAN YOU BUY FROM US?
All kind of pipe tools and plumbing tools, such as pipe threading machine, pipe grooving machine, pipe cutting machine, pipe hole cutter, manual pipe bender, pipe vice as well as the test pump.
4. WHY SHOULD YOU BUY FROM US NOT FROM OTHER SUPPLIERS?
We focus on quality piping tools, machinery and service. We have almost all kind of pipe tools, place order to us we can mix different models in one shipment. Language available:English,Spanish,Japanese,Portuguese,German,Arabic,French,Russian,Korean,Hindi,Italian
5. HOW LONG IS THE LEADTIME?
Since the voltage of machine motors are customized, usually the lead time will be 10-35 days after payment.
6. HOW CAN YOU PLACE ORDER?
We accept T/T payment directly to our company account and we can also create order on the online shop site that you can pay to us by credit card.
7. HOW TO SHIP?
We ship by sea to port for bulk order and we also ship to door for small shipment.
8. WHAT IS THE MOQ?
Basically there is no MOQ required for our machines, we can ship any quantity but it is highly recommened to make order amount not less than USD2000.00, because according to our experience if the order are too small amount the sea shipping adding tarrif makes it not cost-effective to buy oversea.
9. IS OEM ACCEPTABLE?
Yes. For bulk order we can make nameplate and customized packaging in client’s brand.